This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
ecuinputdata [2008/02/15 13:46] dmertz |
ecuinputdata [2009/02/22 09:26] dmertz |
||
---|---|---|---|
Line 7: | Line 7: | ||
**12/19/2007:** We are now accepting orders for these completed units. We have several in stock, ready to ship. | **12/19/2007:** We are now accepting orders for these completed units. We have several in stock, ready to ship. | ||
- | http://www.ecmtuning.com/ordering-buffer.html | + | http://www.ecmtuning.com/product_info.php?cPath=26&products_id=39 |
Line 17: | Line 17: | ||
Connect "GND to ECU" to the ECU's sensor ground, pin 24 (Green/Black) on a 1G ECU or pin 92 (Black) on a 2G ECU. This is also present under the hood at the MAF, TPS, MDP and coolant temp sensors. | Connect "GND to ECU" to the ECU's sensor ground, pin 24 (Green/Black) on a 1G ECU or pin 92 (Black) on a 2G ECU. This is also present under the hood at the MAF, TPS, MDP and coolant temp sensors. | ||
- | If the sensor is a 5V sensor that draws little current, like a MAP sensor, connect its power, signal and ground connections to the buffer circuit assembly. If the device, such as a wideband, has it's own power and ground, connect only the signal wire to the device. Insulate any unused wires. | + | If the sensor is a 5V sensor that draws little current, like a MAP sensor, connect the sensor's power, signal and ground connections to the input side of the buffer circuit assembly. If the sensing device, such as a wideband, has its own power and ground, connect only the sensing device's signal wire to the input side of the buffer. Insulate any unused wires. |
Line 23: | Line 23: | ||
- | ====== Details ====== | + | |
+ | |||
+ | |||
+ | ====== DIY Details ====== | ||
The following table lists a set of ECU inputs and their internal pull up/pull down resistor configuration. | The following table lists a set of ECU inputs and their internal pull up/pull down resistor configuration. | ||
Line 30: | Line 33: | ||
| EGRTemp | 10k up | - | | | EGRTemp | 10k up | - | | ||
| Baro | float/100k down? | 3.3k down | | | Baro | float/100k down? | 3.3k down | | ||
- | | IAT | 2.2k up / 39k down? | 2.2k up / 39k down? | | + | | IAT | 2.2k up / 39k down | 2.2k up / 39k down | |
- | | Coolant | 2.2k up / 39k down? | 2.2k up / 39k down? | | + | | Coolant | 2.2k up / 39k down | 2.2k up / 39k down | |
| MDP | - | 100k down | | | MDP | - | 100k down | | ||
- | | Rear O2 | - | 220K down | | + | | Rear O2 | - | 220k down | |
Again, the EGRTemp on a 1G and the Baro input on a 2G are problematic for some aftermarket sensors. When feeding certain wideband kits into the EGRTemp input on a 1G, for example, you may see normal A/F ratio readings above 11.5:1 but then the readings flatline there and won't show any value below that. | Again, the EGRTemp on a 1G and the Baro input on a 2G are problematic for some aftermarket sensors. When feeding certain wideband kits into the EGRTemp input on a 1G, for example, you may see normal A/F ratio readings above 11.5:1 but then the readings flatline there and won't show any value below that. |