This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
fuelsettingshelp [2010/02/26 13:10] twdorris |
fuelsettingshelp [2011/05/01 06:33] twdorris |
||
---|---|---|---|
Line 2: | Line 2: | ||
This page describes the basic usage of the Fuel tab in the ECU Config section of the ECMLink application. This page is just a dump and reformat of the same information provided in the help file with the ECMLink application. | This page describes the basic usage of the Fuel tab in the ECU Config section of the ECMLink application. This page is just a dump and reformat of the same information provided in the help file with the ECMLink application. | ||
+ | |||
+ | |||
===== Fuel Adjustments Table ===== | ===== Fuel Adjustments Table ===== | ||
Line 7: | Line 9: | ||
The **Fuel Adjustments Table** allows rpm-based adjustment of the air fuel ratio relative to the ECU's stock operation. Moving a point up (or increasing the adjustment value by typing in the numeric table) makes the mixture richer; lowering it makes the mixture leaner. An adjustment of, say, -5% means multiplying the stock fuel amount by 0.95 (delivering 5% less fuel than stock). Most adjustments will be negative numbers since stock fuel delivery is a rather rich, conservative mixture. Between rpm points, the ECU interpolates between the two adjacent rpm settings. | The **Fuel Adjustments Table** allows rpm-based adjustment of the air fuel ratio relative to the ECU's stock operation. Moving a point up (or increasing the adjustment value by typing in the numeric table) makes the mixture richer; lowering it makes the mixture leaner. An adjustment of, say, -5% means multiplying the stock fuel amount by 0.95 (delivering 5% less fuel than stock). Most adjustments will be negative numbers since stock fuel delivery is a rather rich, conservative mixture. Between rpm points, the ECU interpolates between the two adjacent rpm settings. | ||
- | The adjustment described in the preceeding pargraph is fully applied only when the value for LoadFactor (essentially the same as Airflow/rev, or Boost) is above 1.6 (about 10 psi of boost). Below a LoadFactor of 0.8 (roughly atmospheric pressure) none of the adjustment is applied. Between a LoadFactor of 0.8 and 1.6, the adjustment is applied proportionally. For example, a -5% adjustment value at a LoadFactor of 1.0 results in a -1.25% adjustment actually applied: | + | The adjustment described in the preceeding pargraph is fully applied only when the value for LoadFactor (essentially the same as Airflow/rev [or Boost adjusted by VE]) is above 1.6 (about 10 psi of boost). Below a LoadFactor of 0.8 (roughly atmospheric pressure) none of the adjustment is applied. Between a LoadFactor of 0.8 and 1.6, the adjustment is applied proportionally. For example, a -5% adjustment value at a LoadFactor of 1.0 results in a -1.25% adjustment actually applied: |
Real adj = -5% * (1.0 - 0.8) / (1.6 - 0.8) = -1.25% | Real adj = -5% * (1.0 - 0.8) / (1.6 - 0.8) = -1.25% | ||
- | Multiple contiguous fuel adjustment points may be selected by holding the Shift key and using the mouse or the left/right arrow keys, and adjusted simultaneously in equal increments using the up/down arrow keys. | + | Multiple contiguous fuel adjustment points may be selected by holding the Shift key and using the mouse or the left/right arrow keys, and adjusted simultaneously in equal increments using the up/down arrow keys or dragging with the mouse up/down. |
===== Settings ===== | ===== Settings ===== | ||
The **Global fuel** and **Deadtime** adjustments are intended to be used mainly to compensate for injectors and fuel pressure that differ from stock. They are applied at all times. | The **Global fuel** and **Deadtime** adjustments are intended to be used mainly to compensate for injectors and fuel pressure that differ from stock. They are applied at all times. | ||
+ | |||
Line 27: | Line 30: | ||
FlowRateAdj1G = squareroot(BaseFuelPressure / 37) | FlowRateAdj1G = squareroot(BaseFuelPressure / 37) | ||
FlowRateAdj2G = squareroot(BaseFuelPressure / 42.6) | FlowRateAdj2G = squareroot(BaseFuelPressure / 42.6) | ||
+ | FlowRateAdjEVO1-3 = squareroot(BaseFuelPressure / 42.6) | ||
NewInjFlow = InjectorCCPerMin * FlowRateAdj | NewInjFlow = InjectorCCPerMin * FlowRateAdj | ||
Adj = (100 * ( 450 / NewInjFlow ) ) - 100 | Adj = (100 * ( 450 / NewInjFlow ) ) - 100 |