howto
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
howto [2008/01/23 08:51] 76.100.119.159 |
howto [2024/03/15 11:16] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== How-To's ====== | ====== How-To's ====== | ||
| This page is a collection of how-to's from those that have-done. | This page is a collection of how-to's from those that have-done. | ||
| + | |||
| ===== Hardware ===== | ===== Hardware ===== | ||
| Line 10: | Line 11: | ||
| * [[UseNitrousControlsForDejonToolBOVMod|"Nitrous" control used for BOV bypass mod]] - Describes one alternative use of DSMLink's "nitrous" controls | * [[UseNitrousControlsForDejonToolBOVMod|"Nitrous" control used for BOV bypass mod]] - Describes one alternative use of DSMLink's "nitrous" controls | ||
| * [[InstallNewSensor|Install a sensor for datalogging]] - Describes how to use a non-factory sensor for datalogging (e.g., a boost sensor, a wideband kit, etc.) | * [[InstallNewSensor|Install a sensor for datalogging]] - Describes how to use a non-factory sensor for datalogging (e.g., a boost sensor, a wideband kit, etc.) | ||
| + | * [[boostcontrol|ECU-based boost control]] - All the information you need to enable boost control from inside the ECU. | ||
| + | * [[sdsetup|Speed Density Setup]] - Information on setting up your system for speed density operation | ||
| ===== Tuning/dial-in ===== | ===== Tuning/dial-in ===== | ||
| + | * [[BasicFuelAdj|Changing injectors]] - Describes how to adjust DSMLink for different injectors | ||
| + | * [[v3mafadjcombft|General MAF calibration]] - How-to on general MAF calibration with the V3 application | ||
| * [[MAFTCalibrationByWBO2|MAFT Calibration using a WBO2]] - Describes how to calibrate a MAFT output using a WBO2 | * [[MAFTCalibrationByWBO2|MAFT Calibration using a WBO2]] - Describes how to calibrate a MAFT output using a WBO2 | ||
| * [[MAFTCalibrationByLoggedBoost|MAFT Calibration using a boost sensor]] - Describes how to calibrate a MAFT output using a boost sensor | * [[MAFTCalibrationByLoggedBoost|MAFT Calibration using a boost sensor]] - Describes how to calibrate a MAFT output using a boost sensor | ||
| - | * [[CreateVolumetricEfficiencyMap]] | + | * [[CreateVolumetricEfficiencyMap|Customize the VE table for your setup]] - Create a VE table more suited to your specific setup |
| - | * [[2GTimingIn1GECU]] | + | * [[v3tpsadj|How to dial in TPS/idle switch]] |
| - | * [[DSMLinkTPSAdjustment]] | + | |
| - | + | ||
| - | ===== Alternate OS'es ===== | + | |
| - | * [[LinuxInstall]] | ||
| - | * [[MacOSInstall]] | ||
| - | * [[PocketPCInstall]] | ||
| + | ===== Direct Access ===== | ||
| + | * [[Direct Access changes]] - Describes how to add custom changes to Direct Access | ||
howto.1201096264.txt.gz · Last modified: 2008/01/23 08:51 by 76.100.119.159
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
