User Tools

Site Tools


howto

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
howto [2008/01/23 09:14]
76.100.119.159
howto [2024/03/15 11:16] (current)
Line 1: Line 1:
 ====== How-To'​s ====== ====== How-To'​s ======
 This page is a collection of how-to'​s from those that have-done.  ​ This page is a collection of how-to'​s from those that have-done.  ​
 +
  
 ===== Hardware ===== ===== Hardware =====
Line 10: Line 11:
   * [[UseNitrousControlsForDejonToolBOVMod|"​Nitrous"​ control used for BOV bypass mod]] - Describes one alternative use of DSMLink'​s "​nitrous"​ controls   * [[UseNitrousControlsForDejonToolBOVMod|"​Nitrous"​ control used for BOV bypass mod]] - Describes one alternative use of DSMLink'​s "​nitrous"​ controls
   * [[InstallNewSensor|Install a sensor for datalogging]] - Describes how to use a non-factory sensor for datalogging (e.g., a boost sensor, a wideband kit, etc.)   * [[InstallNewSensor|Install a sensor for datalogging]] - Describes how to use a non-factory sensor for datalogging (e.g., a boost sensor, a wideband kit, etc.)
 +  * [[boostcontrol|ECU-based boost control]] - All the information you need to enable boost control from inside the ECU.
 +  * [[sdsetup|Speed Density Setup]] - Information on setting up your system for speed density operation
  
 ===== Tuning/​dial-in ===== ===== Tuning/​dial-in =====
  
 +  * [[BasicFuelAdj|Changing injectors]] - Describes how to adjust DSMLink for different injectors
 +  * [[v3mafadjcombft|General MAF calibration]] - How-to on general MAF calibration with the V3 application
   * [[MAFTCalibrationByWBO2|MAFT Calibration using a WBO2]] - Describes how to calibrate a MAFT output using a WBO2   * [[MAFTCalibrationByWBO2|MAFT Calibration using a WBO2]] - Describes how to calibrate a MAFT output using a WBO2
   * [[MAFTCalibrationByLoggedBoost|MAFT Calibration using a boost sensor]] - Describes how to calibrate a MAFT output using a boost sensor   * [[MAFTCalibrationByLoggedBoost|MAFT Calibration using a boost sensor]] - Describes how to calibrate a MAFT output using a boost sensor
   * [[CreateVolumetricEfficiencyMap|Customize the VE table for your setup]] - Create a VE table more suited to your specific setup   * [[CreateVolumetricEfficiencyMap|Customize the VE table for your setup]] - Create a VE table more suited to your specific setup
-  * [[2GTimingIn1GECU|Settings to run 2G timing in a 1G]] +  * [[v3tpsadj|How to dial in TPS/idle switch]]
-  * [[DSMLinkTPSAdjustment|How to dial in TPS/idle switch]] +
- +
-===== Alternate OS'es =====+
  
-  * [[LinuxInstall|Linux install]] 
-  * [[MacOSInstall|MacOS install]] 
-  * [[PocketPCInstall|PocketPC install]] 
  
 +===== Direct Access =====
 +  * [[Direct Access changes]] - Describes how to add custom changes to Direct Access
  
howto.1201097676.txt.gz · Last modified: 2008/01/23 09:14 by 76.100.119.159