This is an old revision of the document!
The following has been copied from the DSMLink forums. The original (courtesy of Ron Francis) may be found at in this user support forum thread. The text below has been updated to include 1g-specific info, as well as other minor edits.
Example: If LTFT-Lo is at a constant +5%, add +5% to the 50 Hz slider in the airflow table. If the LTFT-Lo is at a constant +12.5% and STFT is at +13%, add +26% to the 50 Hz slider in the airflow table. Repeat until you are happy.
!!!Rev Tuning (STFT) 150hz
1.After you are done with idle tuning, rev the engine and keep it at the 150 Hz level. 1.Watch your STFT's for needed adjustments. 1.If STFT fuel trims are positive, add air at the 150 Hz point in the airflow table. 1.If STFT fuel trims are negative, subtract air at the 150 Hz point in the airflow table. 1.Adjust the airflow 1% for each 1% fuel trims are adjusting fuel.
EXAMPLE: If STFT’s are bouncing between “”+14%“” and “”+16%“”, add “”+15%“” to the 150 Hz slider in the airflow table. Repeat until you are happy.
!!!Cruise Tuning (LTFT-Mid +OR+ LTFT-Hi) 250hz
1.Drive on the freeway at a steady speed to get stable fuel trims. 1.If the fuel trim is positive, add air at the 250 Hz point in the airflow table. 1.If fuel trim is negative, subtract air at the 250 Hz point in the airflow table. 1.Adjust the airflow 1% for each 1% fuel trims are adjusting fuel.
EXAMPLE: If the fuel trim is at a constant “”+7%“”, add “”+7%“” to the 250 Hz slider in the airflow table. Repeat until you are happy.
!!!WOT Tuning (A/F Ratio, WBO2, & ““MAFRaw””) 400hz, 800hz, 1200hz, 1600hz, 2000hz, 2400hz
1.It is easier to do this if A/F Ratio is right above WBO2 in the DSMLink application. 1.After a 3rd gear pull from 1500rpm to redline study the relationship between A/F Ratio and WBO2 at each ""MAFRaw"" Hz point. 1.Adjust the airflow at each ""MAFRaw"" Hz point in the Airflow Table using the associated Hz point in the log. 1.When A/F Ratio is richer than WBO2 at add airflow. OR when A/F Ratio is below WBO2 on the graph, add airflow to move A/F Ratio up. OR when you want more fuel, add more airflow. 1.When A/F Ratio is leaner than WBO2 subtract airflow. OR when A/F Ratio is above WBO2 on the graph, subtract airflow to move A/F Ratio down. OR when you want less fuel, subtract airflow. 1.For each 0.10 A/F Ratio is off, adjust by 1% airflow.
EXAMPLE: You make a pull and you get the following results:
““MAFRaw”” (hz) | 400 | 800 | 1200 | 1600 | 2000 | 2400 | |||||||
A/F Ratio | 9.3 | 9.5 | 9.4 | 9.2 | 9.3 | 9.5 | |||||||
WBO2 | 11.0 | 12.0 | 10.7 | 9.6 | 9.6 | 9.4 | |||||||
Adjustment | “”+17%““ | ””+25%““ | ””+13%““ | ””+4%““ | ””+3%““ | ””-1%““ |
!!!Notes