User Tools

Site Tools


maftcalibrationbywbo2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
maftcalibrationbywbo2 [2008/01/23 08:09]
76.100.119.159
maftcalibrationbywbo2 [2024/03/15 11:16] (current)
Line 1: Line 1:
-====== ​History ​======+====== ​MAFT Calibration by Logged WBO2 ======
  
-The following has been copied from the DSMLink forums. The original (courtesy of Ron Francis) may be found at in this [[http://www.dsmlink.com/​forums/​showthread.php?​t=3529|user support forum thread]]. The text below has been updated to include 1g-specific info, as well as other minor edits.+The following has been copied from the DSMLink forums. The original (courtesy of Ron Francis) may be found at in this [[https://www.ecmtuning.com/​forums/​showthread.php?​t=3529|user support forum thread]] ​(registered DSMLink users only). The text below has been updated to include 1g-specific info, as well as other minor edits.
  
 ====== Assumptions ====== ====== Assumptions ======
Line 55: Line 55:
  
 Example: If the fuel trim is at a constant +7%, add +7% to the 250 Hz slider in the airflow table. Repeat until you are happy. Example: If the fuel trim is at a constant +7%, add +7% to the 250 Hz slider in the airflow table. Repeat until you are happy.
 +
 +
 +
 +
  
 ====== WOT Tuning (A/F Ratio, WBO2, & MAFRaw) 400hz, 800hz, 1200hz, 1600hz, 2000hz, 2400hz ====== ====== WOT Tuning (A/F Ratio, WBO2, & MAFRaw) 400hz, 800hz, 1200hz, 1600hz, 2000hz, 2400hz ======
Line 64: Line 68:
     * When A/F Ratio is leaner than WBO2 subtract airflow. OR when A/F Ratio is above WBO2 on the graph, subtract airflow to move A/F Ratio down. OR when you want less fuel, subtract airflow.     * When A/F Ratio is leaner than WBO2 subtract airflow. OR when A/F Ratio is above WBO2 on the graph, subtract airflow to move A/F Ratio down. OR when you want less fuel, subtract airflow.
     * For each 0.10 A/F Ratio is off, adjust by 1% airflow.     * For each 0.10 A/F Ratio is off, adjust by 1% airflow.
 +
  
 Example: You make a pull and you get the following results: Example: You make a pull and you get the following results:
Line 71: Line 76:
 | WBO2        | 11.0| 12.0|  10.7|   ​9.6| ​  ​9.6| ​  9.4| | WBO2        | 11.0| 12.0|  10.7|   ​9.6| ​  ​9.6| ​  9.4|
 | Adjustment ​ | +17%| +25%|  +13%|   ​+4%| ​  ​+3%| ​  -1%| | Adjustment ​ | +17%| +25%|  +13%|   ​+4%| ​  ​+3%| ​  -1%|
 +
 +**Note:** The following calculation method provides a crude approximation of the needed adjustment and depends on the estimated and measured A/F ratio values being somewhere near 10:1.  Use ECMLink'​s correctly calculated WBFactor value instead.
 +
 +A simple formula for calculating this is:<​code>​
 +(est a/f - WB02) * (-10) = airflow adjustment amount.
 +
 +Example:
 +MAFRaw (hz)  800  ​
 +A/F Ratio    9.5                               
 +WBO2      ​12.0 ​                             ​
 +Adjustment ​ + 25%  ​
 +
 +(9.5 - 12.0) * (- 10)                        ​
 +      (-2.5) ​  * (- 10)                                     
 +        = 25% 
 +
 +(submitted by Omar R. "​DSMmaniac_Big_O"​) </​code> ​    
  
 ====== Notes ====== ====== Notes ======
Line 81: Line 103:
   * Sometimes tuning using a HZ point 100 more than what you are tuning, works better. So, instead of 1200 Hz sometimes using 1300 Hz works better. ​   * Sometimes tuning using a HZ point 100 more than what you are tuning, works better. So, instead of 1200 Hz sometimes using 1300 Hz works better. ​
   * This is not the "​Ideal,​ Perfect"​ way to tune a MAFT, but it was sure easy. As with any tuning the main problem arises with boost leaks and fuel delivery discrepancies. So long as you have no boost leaks and your fuel system is working properly, this is an extremely easy and viable way to tune a MAFT.   * This is not the "​Ideal,​ Perfect"​ way to tune a MAFT, but it was sure easy. As with any tuning the main problem arises with boost leaks and fuel delivery discrepancies. So long as you have no boost leaks and your fuel system is working properly, this is an extremely easy and viable way to tune a MAFT.
 +
maftcalibrationbywbo2.1201093766.txt.gz ยท Last modified: 2008/01/23 08:09 by 76.100.119.159