User Tools

Site Tools


sdveadjsdratio

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
sdveadjsdratio [2009/06/11 12:15]
twdorris
sdveadjsdratio [2010/10/04 04:43]
dmertz
Line 1: Line 1:
 ====== SD VE Adjust (SDRatio) ====== ====== SD VE Adjust (SDRatio) ======
-First and foremost, let's make it clear what this page is all about.  ​This page describes an adjustment tool in the ECMLink application that helps to dial in your speed density (SD) VE table based on data collected from a mass airflow sensor. ​ If you do not plan to run speed density mode with your car or you do plan to run SD but do not have a mass airflow sensor installed for dial-in, then this page is completely useless to you and you should ignore it.+This page describes an adjustment tool in the ECMLink application that helps to dial in your speed density (SD) VE table based on data collected from a mass airflow sensor. ​ If you do not plan to run speed density mode with your car or you do plan to run SD but do not have a mass airflow sensor installed for dial-in, then this page is completely useless to you and you should ignore it.
  
 If you're not even sure what speed density mode means, then read up on our [[sd101|Speed Density 101]] page. If you're not even sure what speed density mode means, then read up on our [[sd101|Speed Density 101]] page.
Line 11: Line 11:
  
 The [[v3mafadjcombft|MAFComp Adjust (CombinedFT)]] page describes an excellent process for dialing in your mass airflow sensor. ​ Please read through this page carefully and make sure your mass airflow setup is calibrated as well as you can get it before attempting to use the **SD VE Adjust (SDRatio)** function. The [[v3mafadjcombft|MAFComp Adjust (CombinedFT)]] page describes an excellent process for dialing in your mass airflow sensor. ​ Please read through this page carefully and make sure your mass airflow setup is calibrated as well as you can get it before attempting to use the **SD VE Adjust (SDRatio)** function.
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
  
  
Line 17: Line 30:
  
 ====== STEP 2: Data Capture ====== ====== STEP 2: Data Capture ======
-To use this tool, you need to capture some data from your ECU while you drive around on the mass airflow sensor. ​ +To use this tool, you need to capture some data from your ECU while you drive around on the mass airflow sensor, before switching the Base MAF setting to Speed Density.
  
-{{  http://www.ecmtuning.com/​images/​forums/​sddata/​sdmaploc.png}} +**NOTE:**  As normally installed, first generation (not Gen 2 or MAFT Pro) MAF translators get their ground from ECU sensor ground via the Mitsubishi MAF connector and draw a moderate amount of current, particularly when powering the GM MAF sensor at higher airflow, so the pressure and temperature readings seen by the ECU will change a little if you later unplug the GM MAF or MAF translator, upsetting the VE table calibration ​Changing the translator'​s ground from ECU sensor ground to chassis ground instead will eliminate this effectCut the MAF translator'​s ground wire between the translator box and the Mitsubishi MAF connector and connect the end of this wire coming from the translator ​to chassis ground. Leave the wire end that remains on the translators Mitsubishi MAF connector isolated ​and insulated.
-Add the following log items to your captured values (F10): SDRatio ​and MAP sensor+
  
-The MAP sensor you want to log here is the one you have already configured in your **Manifold pressure (MAP)** field on the ECU Input tabs.  An example of this is shown here.  More details on configuring and installing this sensor can be found on the [[sdsetup|ECMLink - Speed Density Setup]] page.+Add the following log items to your captured values (F10): SDRatio and MAP sensor. ​ If SDRatio does not appear as an item available for capture, you first need to define the MAP sensor input on the **Pin Assignments for Datalogging (PC-side)** of the **ECU Inputs** tab. 
 + 
 +**SDRatio and engine displacement:​** It's very important to make sure SDRatio'​s engine displacement preference is set correctly to match your actual engine. ​ Do this by double clicking on SDRatio in the graph legend. 
 + 
 +{{  http://​www.ecmtuning.com/​images/​forums/​sddata/​sdmaploc.png}}The MAP sensor you want to log here is the one you have already configured in your **Manifold pressure (MAP)** field on the ECU Input tabs.  An example of this is shown here.  More details on configuring and installing this sensor can be found on the [[sdsetup|ECMLink - Speed Density Setup]] page.
  
 When attempting to initialize the **SD VE Adjust (SDRatio)** tool, the application will check your ECU Input tab to locate the MAP sensor. ​ It will then attempt to find this sensor in your datalog. ​ Using the image above as an example, you would want to log the GM 3-bar sensor attached to the MDP input in order to use this function. When attempting to initialize the **SD VE Adjust (SDRatio)** tool, the application will check your ECU Input tab to locate the MAP sensor. ​ It will then attempt to find this sensor in your datalog. ​ Using the image above as an example, you would want to log the GM 3-bar sensor attached to the MDP input in order to use this function.
  
 +While running off the mass airflow sensor, you basically just drive around logging the data above (SDRatio and MAP sensor) in your datalog. ​ Try to drive under a variety of conditions (idle, cruise, wide open throttle). ​ I like to locate a nice hilly area so I can vary throttle position, RPM and boost to generate the data I'm looking for.
  
  
-====== STEP 3: Drive Around on the Mass Airflow Sensor ====== 
-That's literally it.  While running off the mass airflow sensor, you basically just drive around logging the data above (SDRatio and MAP sensor) in your datalog. ​ Try to drive under a variety of conditions (idle, cruise, wide open throttle). ​ I like to locate a nice hilly area so I can vary throttle position, RPM and boost to generate the data I'm looking for. 
  
 +
 +====== STEP 3: Run the Adjustment Tool ======
 When you're done, you right click in the graph area and select the **SD VE Adjust (SDRatio)** menu item.  The application will then make a number of suggested changes to your SD VE table. ​ You will definitely want to smooth and tweak this data a bit to make it "look nice"​. ​ The application is just going to slap numbers into cells that it has data for.  You'll need to extrapolate that data a bit to areas where you don't normally drive if you want to make the table work well in unexpected conditions. When you're done, you right click in the graph area and select the **SD VE Adjust (SDRatio)** menu item.  The application will then make a number of suggested changes to your SD VE table. ​ You will definitely want to smooth and tweak this data a bit to make it "look nice"​. ​ The application is just going to slap numbers into cells that it has data for.  You'll need to extrapolate that data a bit to areas where you don't normally drive if you want to make the table work well in unexpected conditions.
  
  
 ====== NOTES AND TIPS: Things to Keep in Mind ====== ====== NOTES AND TIPS: Things to Keep in Mind ======
 +
 +
 +
  
  
Line 45: Line 65:
  
 The downside, of course, is that if you disable the air temp sensor for speed density operation inside the ECU, then you need to make sure your air temperature reading while doing your calibration drive is fairly reasonable (say between 50-90F). ​ A good working intercooler and some careful attention to your right foot will help immensely with this too. The downside, of course, is that if you disable the air temp sensor for speed density operation inside the ECU, then you need to make sure your air temperature reading while doing your calibration drive is fairly reasonable (say between 50-90F). ​ A good working intercooler and some careful attention to your right foot will help immensely with this too.
 +
 +Also, since the ECU's Baro input is in use by the Mitsubishi MAF sensor and unavailable for aftermarket-sensor connection, you'll have to use some other ECU input for the MAP sensor (at least until you switch full-time to speed-density and can then move the MAP sensor to the Baro input, if you so choose).
 +
 +
  
  
Line 54: Line 78:
 As long as the GM MAF stayed connected, the offset simply remained constant and you would never really notice much effect. ​ But when you switch to SD, you fully expect to disconnect the GM MAF sensor and that's when the offset makes a difference! ​ Suddenly the pressure sensor output changes relative to what it was when you were dialing the SD setup in using your GM MAF sensor. As long as the GM MAF stayed connected, the offset simply remained constant and you would never really notice much effect. ​ But when you switch to SD, you fully expect to disconnect the GM MAF sensor and that's when the offset makes a difference! ​ Suddenly the pressure sensor output changes relative to what it was when you were dialing the SD setup in using your GM MAF sensor.
  
-To ensure that this isn't a problem, you have to use one of our newer GM MAF cables that provide a separate power wire for the GM MAF's grounding point or you need to [[gmmafcablemod|modify our older GM MAF cable]] (if that's what you have) to add this wire.  If you're running a GM MAF Translator device, you could probably ​do the same ground wire modification as we recommend ​for our older GM MAF cables, but I can't guarantee that.+To ensure that this isn't a problem, you have to use one of our newer GM MAF cables that provide a separate power wire for the GM MAF's grounding point or you need to [[gmmafcablemod|modify our older GM MAF cable]] (if that's what you have) to add this wire. 
 + 
 +If you're running a GM MAF Translator device, you need to do [[gmmafcablemod|a similar ​modification]] on their GM MAF connector ​as was detailed ​for our older cables. ​ This modification involves simply cutting the ground wire on the GM MAF connector and running it to chassis ground instead.
  
sdveadjsdratio.txt · Last modified: 2024/03/15 11:16 (external edit)