use_ecmlink_in_98_99_dsm
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Next revision Both sides next revision | ||
|
use_ecmlink_in_98_99_dsm [2011/05/19 08:18] twdorris created |
use_ecmlink_in_98_99_dsm [2013/04/26 05:46] twdorris |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== How to run ECMLink in a 98/99 DSM ====== | ====== How to run ECMLink in a 98/99 DSM ====== | ||
| - | To run ECMLink in a 98/99 DSM, you will need to first locate a suitable ECU replacement. The 98/99 DSM ECUs do not support our flash module modification. We do not have plans to support the 98/99 DSM ECU yet because of copy protection concerns. So for the time being, you must run a 95, 96 or 97 ECU in your 98/99 DSM in order to use ECMLink. | + | To run ECMLink in a 98/99 DSM, you will need to first locate a suitable ECU replacement. The 98/99 DSM ECUs do not support our flash module modification. We do not have plans to support the 98/99 DSM ECU yet because of copy protection concerns. So for the time being, you must run a 95, 96 or 97 ECU in your 98/99 DSM in order to use ECMLink. These are direct, plug-in replacements for the 98/99 ECUs with the minor exceptions noted below. |
| ===== ECU Details ===== | ===== ECU Details ===== | ||
| For the 2G DSMs, there are a few different types of ECUs that are compatible with ECMLink. | For the 2G DSMs, there are a few different types of ECUs that are compatible with ECMLink. | ||
| - | * 95 EPROM ECU | + | * 95 EPROM ECU (MD312464 or MD309947 with "E" on [[http://www.dsmlink.com/images/photos/eculabel-mid.gif|the case label]]) |
| - | * 95 non-EPROM ECU | + | * 95 non-EPROM ECU (MD312464 or MD309947 without "E" on [[http://www.dsmlink.com/images/photos/eculabel-mid.gif|the case label]]) |
| - | * 96 non-EPROM ECU | + | * 96 non-EPROM ECU (MD321911 or MD321912) |
| - | * 97 non-EPROM ECU | + | * 97 non-EPROM ECU (MD326328 or MD335287) |
| - | The following sections break each of these down for you. | + | The following sections break each of these down for you. We do usually have ECUs in stock too, if you can't find one yourself. We sell them directly off [[http://www.ecmtuning.com/product_info.php?cPath=24&products_id=41|our website]] with new ECMLink package purchases. |
| ==== Using a 95 EPROM ECU ==== | ==== Using a 95 EPROM ECU ==== | ||
| Line 20: | Line 21: | ||
| When you place your ECMLink order off our website, you will simply select "Socket EPROM ECU" as your socket/conversion option at the bottom of the page. | When you place your ECMLink order off our website, you will simply select "Socket EPROM ECU" as your socket/conversion option at the bottom of the page. | ||
| + | |||
| + | |||
| + | |||
| ==== Using a 95 or 96 non-EPROM ECU ==== | ==== Using a 95 or 96 non-EPROM ECU ==== | ||
| - | You can use a 95 or 96 non-EPROM ECU if you absolutely have to. But if you're going to use a non-EPROM ECU anyway, it's better to try to locate 97 non-EPROM ECU. | + | You can use a 95 or 96 non-EPROM ECU but it will need to have our non-EPROM to EPROM conversion installed. |
| + | |||
| + | While installing the conversion we will move jumper J5 to J1 to convert the ECU to a 97. You do not need to swap the plug wires or check the cam angle sensor checkbox because the 97 ECU was made to work with the same cam angle sensor as found on a 98/99 DSM. | ||
| If you do decide to use a 95 or 96 non-EPROM ECU, then you will need to select "2G non-EPROM conversion" in the socket/conversion option at the bottom of the ECMLink ordering page. | If you do decide to use a 95 or 96 non-EPROM ECU, then you will need to select "2G non-EPROM conversion" in the socket/conversion option at the bottom of the ECMLink ordering page. | ||
| - | You will also need to swap your plug wires and check the cam angle sensor checkbox as described above for a 95 EPROM ECU. | + | **ORDERING NOTE:** Be sure to note in the order that the ECU will be used in a 97 or later car so that we know to move the cam-signal inversion jumper. |
| ==== Using a 97 non-EPROM ECU ==== | ==== Using a 97 non-EPROM ECU ==== | ||
use_ecmlink_in_98_99_dsm.txt · Last modified: 2024/03/15 11:16 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
