innovatelc1orlm1install
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
innovatelc1orlm1install [2011/03/06 12:07] snowborder714 |
innovatelc1orlm1install [2024/03/15 11:16] (current) |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| **Version Check:** Please take note of the version of LM Programmer shown in the screenshots. There are newer versions (v3.19 and 3.27) that are shipping with the units that Innovate knows does not function as it should. For some reason, they do not mention this anywhere. The easiest way to determine if the version you have works is to make the changes below, click the Program button, and then go back in and see if the settings were retained. The most recent version __does not__ hold your changes. The latest known working version is v3.15. Until Innovate provides a fix for this, you can download the older v3.15 software here: | **Version Check:** Please take note of the version of LM Programmer shown in the screenshots. There are newer versions (v3.19 and 3.27) that are shipping with the units that Innovate knows does not function as it should. For some reason, they do not mention this anywhere. The easiest way to determine if the version you have works is to make the changes below, click the Program button, and then go back in and see if the settings were retained. The most recent version __does not__ hold your changes. The latest known working version is v3.15. Until Innovate provides a fix for this, you can download the older v3.15 software here: | ||
| - | http://www.ecmtuning.com/images/forums/lc1install/LMConfig315.exe | + | https://www.ecmtuning.com/images/forums/lc1install/LMConfig315.exe |
| Line 20: | Line 20: | ||
| ===== Analog out configuration ===== | ===== Analog out configuration ===== | ||
| - | {{http://www.dsmlink.com/images/forums/lc1install/analog01.jpg}} | + | {{https://www.ecmtuning.com/images/forums/lc1install/analog01.jpg}} |
| - | {{http://www.dsmlink.com/images/forums/lc1install/analog02.jpg}} | + | {{https://www.ecmtuning.com/images/forums/lc1install/analog02.jpg}} |
| ===== Copper heatsink fabrication ===== | ===== Copper heatsink fabrication ===== | ||
| Line 30: | Line 30: | ||
| Use a 4" x 4" (10cm x 10cm) sheet of copper sheet metal 14ga (1.5mm thick). Drill a hole in the center with the same diameter as the oxygen sensor threads (about 3/4" or 19mm). Fold the sides up 45° and mount it between the sensor and the bung like you would a big washer. Orient it such that the sides are exposed to good airflow. | Use a 4" x 4" (10cm x 10cm) sheet of copper sheet metal 14ga (1.5mm thick). Drill a hole in the center with the same diameter as the oxygen sensor threads (about 3/4" or 19mm). Fold the sides up 45° and mount it between the sensor and the bung like you would a big washer. Orient it such that the sides are exposed to good airflow. | ||
| - | {{http://www.dsmlink.com/images/forums/lc1install/CopperHeatSink.jpg}} | + | {{https://www.ecmtuning.com/images/forums/lc1install/CopperHeatSink.jpg}} |
| - | {{http://www.dsmlink.com/images/forums/lc1install/CopperHeatSink00.jpg}} | + | {{https://www.ecmtuning.com/images/forums/lc1install/CopperHeatSink00.jpg}} |
| - | {{http://www.dsmlink.com/images/forums/lc1install/CopperHeatSink01.jpg}} | + | {{https://www.ecmtuning.com/images/forums/lc1install/CopperHeatSink01.jpg}} |
| + | |||
| + | {{https://www.ecmtuning.com/images/forums/lc1install/CopperHeatSink02.jpg}} | ||
| - | {{http://www.dsmlink.com/images/forums/lc1install/CopperHeatSink02.jpg}} | ||
innovatelc1orlm1install.1299431254.txt.gz · Last modified: 2011/03/06 12:07 by snowborder714
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
